Fuootech Oil Filtration Group
Series FTTR-10000 Transformer Turns Ratio Test Set
  • Series FTTR-10000 Transformer Turns Ratio Test Set

Series FTTR-10000 Transformer Turns Ratio Test Set

Series FTTR-10000 is single phase,automatically test set specially 
designed for turns ratio, phase shift and excitation current measurements 
of power, distribution and instrument transformer.

  • Share This Post:

     According to IEC and related regulations, Transformer oil turns ratio test must be done before the transformers (semi-finished, finished, newly-installed or repaired) are put into operation, also periodical test should be done during the operation.

     

     Through this test procedure, you can check the transformer winding turns ratio and tap switch and find out if there is any defects such as interturn short circuit (coils short circuit tester) in transformers and if can proceed Parallel operation, etc… so as to protect the electrical equipments.

     

       Series FTTR-10000 Transformer Turns Ratio Test Set is special designed to help do this test and has been widely used in electrical industrials and grids.


     

     Wide test range, the maximum is up to 10000.

     Fully automatic: no manual balancing required

     Suitable for Testing single phase transformers

     Automatic measure transformer connection group

     Automatic switching measuring range

     Automatic switching phase sequence.

     Automatic process transformation of group

     Automatic calibrating meter.

     Automatic calculation of ratio error after input standard turns ratio.

     When test tap changer transformer, only need to input one turns ratio.

     Test results saved automatically

     Recall and print last 30 test results

     Prints results on built-in printer

     Automatic cut off test voltage after one test is completed.

     Micro-controller operated

     Small size, light weight.


     

     Test Range: 1 ~ 10000

     Accuracy:  0.2%  (1 ~ 1000) 
                            0.5%  (1000 ~ 10000)

     Power supply: AC220V ± 10%, 50 Hz 

     Use temperature: -5 ° C to 40 ° C

     Relative humidity: ≤ 85%, 

     Dimension:  430mm × 320mm × 215mm 

     Net Weight:  8 Kg


    Note:    1. The dimension and weight will be changed with changing of technical specs.

                 2. All the specs can be customized according to client's requirements.

       For more info, pls don't hesitate to contact us.

     

Top
Series FTTR-10000 Transformer Turns Ratio Test Set

Series FTTR-10000 Transformer Turns Ratio Test Set

Series FTTR-10000 is single phase,automatically test set specially 
designed for turns ratio, phase shift and excitation current measurements 
of power, distribution and instrument transformer.

     According to IEC and related regulations, Transformer oil turns ratio test must be done before the transformers (semi-finished, finished, newly-installed or repaired) are put into operation, also periodical test should be done during the operation.

     

     Through this test procedure, you can check the transformer winding turns ratio and tap switch and find out if there is any defects such as interturn short circuit (coils short circuit tester) in transformers and if can proceed Parallel operation, etc… so as to protect the electrical equipments.

     

       Series FTTR-10000 Transformer Turns Ratio Test Set is special designed to help do this test and has been widely used in electrical industrials and grids.


     

     Wide test range, the maximum is up to 10000.

     Fully automatic: no manual balancing required

     Suitable for Testing single phase transformers

     Automatic measure transformer connection group

     Automatic switching measuring range

     Automatic switching phase sequence.

     Automatic process transformation of group

     Automatic calibrating meter.

     Automatic calculation of ratio error after input standard turns ratio.

     When test tap changer transformer, only need to input one turns ratio.

     Test results saved automatically

     Recall and print last 30 test results

     Prints results on built-in printer

     Automatic cut off test voltage after one test is completed.

     Micro-controller operated

     Small size, light weight.


     

     Test Range: 1 ~ 10000

     Accuracy:  0.2%  (1 ~ 1000) 
                            0.5%  (1000 ~ 10000)

     Power supply: AC220V ± 10%, 50 Hz 

     Use temperature: -5 ° C to 40 ° C

     Relative humidity: ≤ 85%, 

     Dimension:  430mm × 320mm × 215mm 

     Net Weight:  8 Kg


    Note:    1. The dimension and weight will be changed with changing of technical specs.

                 2. All the specs can be customized according to client's requirements.

       For more info, pls don't hesitate to contact us.

     

    CONTACT US
  • NO.5 Hongshi Street, Jiulongpo District, Chongqing, China
  • +86 135 2739 0908
  • +86 23 8823 9845
  • +86 23 8823 9845
  • Contact Us   Sitemap
  • Series FTTR-10000 Transformer Turns Ratio Test Set

    Series FTTR-10000 Transformer Turns Ratio Test Set

    Series FTTR-10000 is single phase,automatically test set specially 
    designed for turns ratio, phase shift and excitation current measurements 
    of power, distribution and instrument transformer.

    • Share This Post:

       According to IEC and related regulations, Transformer oil turns ratio test must be done before the transformers (semi-finished, finished, newly-installed or repaired) are put into operation, also periodical test should be done during the operation.

       

       Through this test procedure, you can check the transformer winding turns ratio and tap switch and find out if there is any defects such as interturn short circuit (coils short circuit tester) in transformers and if can proceed Parallel operation, etc… so as to protect the electrical equipments.

       

         Series FTTR-10000 Transformer Turns Ratio Test Set is special designed to help do this test and has been widely used in electrical industrials and grids.


       

       Wide test range, the maximum is up to 10000.

       Fully automatic: no manual balancing required

       Suitable for Testing single phase transformers

       Automatic measure transformer connection group

       Automatic switching measuring range

       Automatic switching phase sequence.

       Automatic process transformation of group

       Automatic calibrating meter.

       Automatic calculation of ratio error after input standard turns ratio.

       When test tap changer transformer, only need to input one turns ratio.

       Test results saved automatically

       Recall and print last 30 test results

       Prints results on built-in printer

       Automatic cut off test voltage after one test is completed.

       Micro-controller operated

       Small size, light weight.


       

       Test Range: 1 ~ 10000

       Accuracy:  0.2%  (1 ~ 1000) 
                              0.5%  (1000 ~ 10000)

       Power supply: AC220V ± 10%, 50 Hz 

       Use temperature: -5 ° C to 40 ° C

       Relative humidity: ≤ 85%, 

       Dimension:  430mm × 320mm × 215mm 

       Net Weight:  8 Kg


      Note:    1. The dimension and weight will be changed with changing of technical specs.

                   2. All the specs can be customized according to client's requirements.

         For more info, pls don't hesitate to contact us.

       

    CONTACT US