Fuootech Oil Filtration Group
Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System
  • Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System
  • Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

It is mainly for treating & regenerating the used and 
old transformer oils which power transformers are 
above 110 kV in the big power station and 
power transmission station

  • Share This Post:

     Series ZYD-R Multi-Stage Vacuum & Double Stage Chamber Type Transformer Oil Regeneration System is developed from Series ZYD-I, which mainly satisfy some clients who want the highest special transformer oil’s quality even higher than new oil’s quality.

     

     It is mainly for treating & regenerating the used and old transformer oil, mutual oil, and switch oil, which power transformers are above 110 kV in the big power station and power transmission station.

     

     The oil’s quality after regenerated by Series ZYD-R is equal or higher than new oil’s quality, which can be used directly into transformers.

     

     This machine can dewater, degas and remove the impurity more deeply with high speed, and improve oil’s BDV Value much higher and faster. Also it can fill the insulating oil into the transformers on-line.  

     

     This system is equipped with Four (2-2) Stages vacuum system which consists 2 sets of double-stage vacuum system can give much higher vacuum degree value, and one of these can be used to pump vacuum from transformers independently.

     

     Series ZYD-R also consist two stages of vacuum degassing and dehydration chambers which is capable of removing large portion of water content and gas/air content from the oil. It’s two times than normal one stage vacuum chamber.

     

     Oil Result after Filtration                                            

    Moisture (Water Content)

    ≤ 3 PPM

    Gas Content

    ≤0.01% (Vol)

    Impurities Degree (Filtration precision)

    ≤ 1 micron (no free carbon)

    Breakdown Voltage (Dielectric)

    ≥75 KV

    Flash Point

    ≥145

    PH Value

    ≥5.5

    Acid Value

    ≤0.03mgkoH/g

    Dielectric loss

    tgδ(90℃)%≤0.001

    Cleanliness

    ≤NAS 1638 Grade 6

     

     Special four stages (2 double-stage vacuum) and two stages of vacuum chambers designed for customers who have the highest requirements on oil’s quality after regeneration.

    Duplex 3D stereo-evaporation technology resulting in eliminating the liquid water content quickly and separating gas/air content fast.

     

    UK G technology is adopted to remove trace water, dissolved water effectively and thoroughly.

     High-tech FH Trapezoidal networking Filtering technology with multi-stage filtering materials ensure the distinctive particles & impurities removal.

     

     Carbon fiber infrared heating system that can make the oil contains zero sum of ethyne after the regeneration.

    Adopt interlocked protective system, which connect oil pump, heater and liquid level sensor, avoiding blank heating, blank pumping, oil leak and electricity leak. If there is any fault, machine will be power off automatically.

    Double-infrared liquid level controlling system keep oil inlet and outlet quantity balancing while operation fully automatically.

     

    Parameters

    Model

    Unit

    ZYD-R-30

    ZYD-R-50

    ZYD-R-100

    ZYD-R-150

    ZYD-R-200

    ZYD-R-250

    ZYD-R-300

    Flow Rate

    L/H

    1800

    3000

    6000

    9000

    12000

    15000

    18000

    Working Vacuum Degree

    MPa

    -0.08 ~ -0.099

    Working

    Discharge Pressure

    MPa

    ≤ 0.3

    Temperature

    Control Range

    20 ~ 80

    Operation Temperature

    40 ~ 70 (65℃ is best)

    Power Supply

    380V, 50Hz, 3 phases (or as per your requirements)

    Working hours

    without Trouble

    Hour

    4000

    Continuous Working Hours

    Hour

    150

    Ambient Temperature

    -25 ~ 55℃

    Working Noise

    dB(A)

    65 ~ 90

    Heating Power

    (adjusted available)

    KW

    30

    36

    48

    60

    72

    80

    120

    Total Power

    KW

    35.5

    42

    52.5

    68

    82

    93

    135

    Inlet/Outlet

    mm

    φ25

    φ32

    φ42

    φ50

    φ50

    φ60

    φ60

    Weight

    Kg

    850

    960

    1080

    1200

    1490

    1700

    2050

    Dimension

    Length

    mm

    1480

    1730

    1830

    1960

    2010

    2070

    2230

    Width

    mm

    1150

    1360

    1390

    1410

    1550

    1660

    1780

    Height

    mm

    1800

    1930

    2170

    2200

    2310

    2400

    2580

      Note:     1. The dimension and weight will be changed with changing of technical specs.

                    2. All the specs can be customized according to client's requirements.

     

        For more info, pls don't hesitate to contact us.

    CONTACT US
  • NO.5 Hongshi Street, Jiulongpo District, Chongqing, China
  • +86 135 2739 0908
  • +86 23 8823 9845
  • +86 23 8823 9845
  •        info#fuootech.com
           (please change # to @ when you need send us inquiries by email.)
Top
Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

It is mainly for treating & regenerating the used and 
old transformer oils which power transformers are 
above 110 kV in the big power station and 
power transmission station

     Series ZYD-R Multi-Stage Vacuum & Double Stage Chamber Type Transformer Oil Regeneration System is developed from Series ZYD-I, which mainly satisfy some clients who want the highest special transformer oil’s quality even higher than new oil’s quality.

     

     It is mainly for treating & regenerating the used and old transformer oil, mutual oil, and switch oil, which power transformers are above 110 kV in the big power station and power transmission station.

     

     The oil’s quality after regenerated by Series ZYD-R is equal or higher than new oil’s quality, which can be used directly into transformers.

     

     This machine can dewater, degas and remove the impurity more deeply with high speed, and improve oil’s BDV Value much higher and faster. Also it can fill the insulating oil into the transformers on-line.  

     

     This system is equipped with Four (2-2) Stages vacuum system which consists 2 sets of double-stage vacuum system can give much higher vacuum degree value, and one of these can be used to pump vacuum from transformers independently.

     

     Series ZYD-R also consist two stages of vacuum degassing and dehydration chambers which is capable of removing large portion of water content and gas/air content from the oil. It’s two times than normal one stage vacuum chamber.

     

     Oil Result after Filtration                                            

    Moisture (Water Content)

    ≤ 3 PPM

    Gas Content

    ≤0.01% (Vol)

    Impurities Degree (Filtration precision)

    ≤ 1 micron (no free carbon)

    Breakdown Voltage (Dielectric)

    ≥75 KV

    Flash Point

    ≥145

    PH Value

    ≥5.5

    Acid Value

    ≤0.03mgkoH/g

    Dielectric loss

    tgδ(90℃)%≤0.001

    Cleanliness

    ≤NAS 1638 Grade 6

     

     Special four stages (2 double-stage vacuum) and two stages of vacuum chambers designed for customers who have the highest requirements on oil’s quality after regeneration.

    Duplex 3D stereo-evaporation technology resulting in eliminating the liquid water content quickly and separating gas/air content fast.

     

    UK G technology is adopted to remove trace water, dissolved water effectively and thoroughly.

     High-tech FH Trapezoidal networking Filtering technology with multi-stage filtering materials ensure the distinctive particles & impurities removal.

     

     Carbon fiber infrared heating system that can make the oil contains zero sum of ethyne after the regeneration.

    Adopt interlocked protective system, which connect oil pump, heater and liquid level sensor, avoiding blank heating, blank pumping, oil leak and electricity leak. If there is any fault, machine will be power off automatically.

    Double-infrared liquid level controlling system keep oil inlet and outlet quantity balancing while operation fully automatically.

     

    Parameters

    Model

    Unit

    ZYD-R-30

    ZYD-R-50

    ZYD-R-100

    ZYD-R-150

    ZYD-R-200

    ZYD-R-250

    ZYD-R-300

    Flow Rate

    L/H

    1800

    3000

    6000

    9000

    12000

    15000

    18000

    Working Vacuum Degree

    MPa

    -0.08 ~ -0.099

    Working

    Discharge Pressure

    MPa

    ≤ 0.3

    Temperature

    Control Range

    20 ~ 80

    Operation Temperature

    40 ~ 70 (65℃ is best)

    Power Supply

    380V, 50Hz, 3 phases (or as per your requirements)

    Working hours

    without Trouble

    Hour

    4000

    Continuous Working Hours

    Hour

    150

    Ambient Temperature

    -25 ~ 55℃

    Working Noise

    dB(A)

    65 ~ 90

    Heating Power

    (adjusted available)

    KW

    30

    36

    48

    60

    72

    80

    120

    Total Power

    KW

    35.5

    42

    52.5

    68

    82

    93

    135

    Inlet/Outlet

    mm

    φ25

    φ32

    φ42

    φ50

    φ50

    φ60

    φ60

    Weight

    Kg

    850

    960

    1080

    1200

    1490

    1700

    2050

    Dimension

    Length

    mm

    1480

    1730

    1830

    1960

    2010

    2070

    2230

    Width

    mm

    1150

    1360

    1390

    1410

    1550

    1660

    1780

    Height

    mm

    1800

    1930

    2170

    2200

    2310

    2400

    2580

      Note:     1. The dimension and weight will be changed with changing of technical specs.

                    2. All the specs can be customized according to client's requirements.

     

        For more info, pls don't hesitate to contact us.

    CONTACT US
  • NO.5 Hongshi Street, Jiulongpo District, Chongqing, China
  • +86 135 2739 0908
  • +86 23 8823 9845
  • +86 23 8823 9845
  • Contact Us   Sitemap
  • Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

    Series ZYD-R Multi-Stage Vacuum Transformer Oil Regeneration System

    It is mainly for treating & regenerating the used and 
    old transformer oils which power transformers are 
    above 110 kV in the big power station and 
    power transmission station

    • Share This Post:

       Series ZYD-R Multi-Stage Vacuum & Double Stage Chamber Type Transformer Oil Regeneration System is developed from Series ZYD-I, which mainly satisfy some clients who want the highest special transformer oil’s quality even higher than new oil’s quality.

       

       It is mainly for treating & regenerating the used and old transformer oil, mutual oil, and switch oil, which power transformers are above 110 kV in the big power station and power transmission station.

       

       The oil’s quality after regenerated by Series ZYD-R is equal or higher than new oil’s quality, which can be used directly into transformers.

       

       This machine can dewater, degas and remove the impurity more deeply with high speed, and improve oil’s BDV Value much higher and faster. Also it can fill the insulating oil into the transformers on-line.  

       

       This system is equipped with Four (2-2) Stages vacuum system which consists 2 sets of double-stage vacuum system can give much higher vacuum degree value, and one of these can be used to pump vacuum from transformers independently.

       

       Series ZYD-R also consist two stages of vacuum degassing and dehydration chambers which is capable of removing large portion of water content and gas/air content from the oil. It’s two times than normal one stage vacuum chamber.

       

       Oil Result after Filtration                                            

      Moisture (Water Content)

      ≤ 3 PPM

      Gas Content

      ≤0.01% (Vol)

      Impurities Degree (Filtration precision)

      ≤ 1 micron (no free carbon)

      Breakdown Voltage (Dielectric)

      ≥75 KV

      Flash Point

      ≥145

      PH Value

      ≥5.5

      Acid Value

      ≤0.03mgkoH/g

      Dielectric loss

      tgδ(90℃)%≤0.001

      Cleanliness

      ≤NAS 1638 Grade 6

       

       Special four stages (2 double-stage vacuum) and two stages of vacuum chambers designed for customers who have the highest requirements on oil’s quality after regeneration.

      Duplex 3D stereo-evaporation technology resulting in eliminating the liquid water content quickly and separating gas/air content fast.

       

      UK G technology is adopted to remove trace water, dissolved water effectively and thoroughly.

       High-tech FH Trapezoidal networking Filtering technology with multi-stage filtering materials ensure the distinctive particles & impurities removal.

       

       Carbon fiber infrared heating system that can make the oil contains zero sum of ethyne after the regeneration.

      Adopt interlocked protective system, which connect oil pump, heater and liquid level sensor, avoiding blank heating, blank pumping, oil leak and electricity leak. If there is any fault, machine will be power off automatically.

      Double-infrared liquid level controlling system keep oil inlet and outlet quantity balancing while operation fully automatically.

       

      Parameters

      Model

      Unit

      ZYD-R-30

      ZYD-R-50

      ZYD-R-100

      ZYD-R-150

      ZYD-R-200

      ZYD-R-250

      ZYD-R-300

      Flow Rate

      L/H

      1800

      3000

      6000

      9000

      12000

      15000

      18000

      Working Vacuum Degree

      MPa

      -0.08 ~ -0.099

      Working

      Discharge Pressure

      MPa

      ≤ 0.3

      Temperature

      Control Range

      20 ~ 80

      Operation Temperature

      40 ~ 70 (65℃ is best)

      Power Supply

      380V, 50Hz, 3 phases (or as per your requirements)

      Working hours

      without Trouble

      Hour

      4000

      Continuous Working Hours

      Hour

      150

      Ambient Temperature

      -25 ~ 55℃

      Working Noise

      dB(A)

      65 ~ 90

      Heating Power

      (adjusted available)

      KW

      30

      36

      48

      60

      72

      80

      120

      Total Power

      KW

      35.5

      42

      52.5

      68

      82

      93

      135

      Inlet/Outlet

      mm

      φ25

      φ32

      φ42

      φ50

      φ50

      φ60

      φ60

      Weight

      Kg

      850

      960

      1080

      1200

      1490

      1700

      2050

      Dimension

      Length

      mm

      1480

      1730

      1830

      1960

      2010

      2070

      2230

      Width

      mm

      1150

      1360

      1390

      1410

      1550

      1660

      1780

      Height

      mm

      1800

      1930

      2170

      2200

      2310

      2400

      2580

        Note:     1. The dimension and weight will be changed with changing of technical specs.

                      2. All the specs can be customized according to client's requirements.

       

          For more info, pls don't hesitate to contact us.

    CONTACT US
    • NO.5 Hongshi Street, Jiulongpo District, Chongqing, China
    • +86-135 2739 0908
    • +86 23 8823 9845
    • +86 23 8823 9845
    •        info#fuootech.com
             (please change # to @ when you need send us inquiries by email.)