Power Transformer DC Winding Resistance Meter DC Resistance Tester/Coil Resistance Tester/Low Resistance Tester 20A

We continue to improve product standardization, serialization, and standardization, pursue and improve brand awareness, establish an excellent corporate image, and make our own contributions to the development of the transformer oil breakdown voltage tester, Breakdown voltage testing of insulating oil, turbine oil purifier system industry. Casting a century-old brand is our driving force, which is the dream and belief of all employees, and we will play hard for it and never stop. Our company's management is standardized and standardized, and carries out all-round professional and technical training for employees. Everything is customer-oriented. We know that the development of the enterprise is inseparable from the care and support of the country and society, and it is always our noble responsibility and grand sentiment to serve the country and give back to the society. We build our brand with rigorous and meticulous spirit and serve customers with a warm and thoughtful attitude.

1. Introduction & Application

Transformer DC resistance is a must-test item for semi-finished products in finished transformer manufacturing, finished product testing, installation, overhaul, change of tap-changer, handover test and preventive test in the power sector.

It is able to check the welding quality of the winding joint and the presence or absence of the turn-to-turn short circuit of the winding, and it is possible to detect whether the contact of each position of the voltage tap changer is good and whether the actual position of the tap changer and the indicated position are consistent, whether the lead wire is broken, and the multi-strand wire is wound. Whether there are broken shares and so on.

In order to meet the needs of rapid measurement of DC resistance of transformers, FUOOTECH developed FTDC-100A DC resistance tester. The whole machine is controlled by high-speed single-chip microcomputer with high degree of automation and automatic discharge and discharge alarm function. The instrument has high test accuracy and easy operation, and can realize rapid measurement of the direct resistance of the transformer.

2. Security Measures

1). Be sure to read this manual carefully before using this instrument.

2). The operator of the instrument should have common knowledge of the use of general electrical equipment or instruments.

3). This instrument can be used indoors and outdoors, but should be used away from rain, corrosive gas and other places.

4). The instrument should avoid severe vibration.

5). Maintenance, care and adjustment of the instrument should be carried out by professionals.

6). After the test is completed, be sure to wait for the discharge alarm sound to stop before turning off the power and remove the test line.

7). To measure the no-load voltage regulating transformer, be sure to switch the gear position after the discharge indicating alarm sound stops.

8). During the test, it is forbidden to move the test clip and power supply line.

3. Technical Parameters

1). The output current: 100A, 50A, 20A, 10A, 5A

2). The minimum resolution: 0.1μΩ

3). Range: 100A: 50μΩ~100mΩ, 50A: 100μΩ~200mΩ

20A: 200μΩ~800mΩ, 10A: 500μΩ~2Ω, 5A: 1mΩ~4Ω.

4). Accuracy: ± (0.2% + 2 words)

5). Weight: 15KG without test line

4. Precautions

1). It is necessary to wait for the discharge to end. After the alarm sound stops, the line is removed again, otherwise it is dangerous.

2). When measuring the unloaded voltage regulating transformer, the discharge must be reset before the reverse tapping, and the switch point can be switched after the alarm sound stops.

3). When selecting current, refer to the range in the technical index column. When the current is over-range, the instrument is always in the "charging" state because the current does not reach the preset value. At this time, press the reset button to reset the instrument and re-select the smaller one. Current gear. When the range is under-balanced, "Current current is too small" is displayed. When these two states occur, the range is confirmed and a larger current is selected for testing.

4). After the test is completed, press the "Reset" button, the instrument power will be disconnected from the winding, discharge at the same time, the audible alarm, the ammeter will return to the zero position, then the display will return to the initial state, and the discharge can be rewired after the end of the discharge. Take the next measurement or remove the test line and the power cord to end the measurement.

5. Stocks at office

6. Packing, Delivery, Shipping and Payment

7. Certificates

8. FAQ

Q1. Are you a manufacturer, trading company or a third party? When and where did your factory established?

FUOOTECH: We are a manufacturer established since 2002, located at Chongqing city, China.

Q2: Can you produce your products as our requirements, such as put on our logo?
FUOOTECH: Yes, OEM and ODM are available. We have the professional technical team to design the products as per your request.

Q3. What's the minimum order quantity?
FUOOTECH: 1 Set.
 

Welcome to contact us for any inquiry and cooperation.

Through deep understanding of our customers, continuous improvement of our brand value and continuous growth of our position in the Power Transformer DC Winding Resistance Meter DC Resistance Tester/Coil Resistance Tester/Low Resistance Tester 20A industry, we have gradually enhanced our growth and competitiveness to provide first-class products and services to our customers. We identify with the curiosity of the audience and enhance our brand image. The company has made unremitting explorations in innovation and established a sound governance structure.